1.用沖擊電鉆在門四周大洞眼,并插入木楔。

1. Use an impact drill to drill large holes around the door and insert wooden wedges.

2.將15厘大芯板(或夾板)靠墻側進行防潮處理(刷光油2遍后在貼珍珠棉)。用釘槍校正固定后,再用鐵釘加固。門套線條打底用9厘夾板。打底夾板外側用實木線條收口。合頁位置加板襯固或封兩層15厘大芯板。

2. Apply moisture-proof treatment to the side of the 15mm large core board (or plywood) against the wall (apply two coats of gloss oil before applying pearl cotton). After correcting and fixing with a nail gun, reinforce with iron nails. Use a 9mm plywood to base the door frame lines. Close the outer side of the bottom plywood with solid wood lines. Add a board lining or seal two layers of 15mm large core board at the hinge position.

3.門套與門扇相合之處到進門邊的側面用9厘夾板做止口板,止口深度與門的厚度相同。

3. Use a 9mm plywood as a stop plate from the junction of the door frame and the door leaf to the side of the entrance door, with the depth of the stop plate being the same as the thickness of the door.

4.面板用白乳膠涂勻后貼于打第大芯板及止口板上,并用不銹鋼蚊釘適當加固。

4. The panel should be evenly coated with white latex and then pasted onto the large core board and stop plate, and appropriately reinforced with stainless steel mosquito nails.

5.門套線條寬度一般為60mm—80mm.厚度8mm.

5. The width of the door frame line is generally 60mm to 80mm, with a thickness of 8mm

6.廚衛門套線條里側用不銹鋼(啞光)線條為宜。

6. It is advisable to use stainless steel (matte) lines on the inner side of the kitchen and bathroom door frames.

7.門套及門窗套垂直、水平誤差不超過2mm(2m以上不超過3mm)對角線誤差不超過3mm(2m以上不超過5mm).

7. The vertical and horizontal errors of door and window frames shall not exceed 2mm (not exceeding 3mm for 2m and above), and the diagonal errors shall not exceed 3mm (not exceeding 5mm for 2m and above)

8.門套兩側墻與門套之間距離在門套線條不能壓住接縫時,宜先用水泥砂漿掛鋼釘封平(用板定模灌漿)干燥后方可封板打第,在門套線條能壓住接縫時可用板封龍骨結構。

When the distance between the walls on both sides of the door frame and the door frame cannot press the joint, it is advisable to first use cement mortar to hang steel nails to seal it flat (using plate fixed mold grouting) and dry it before sealing the board. When the door frame line can press the joint, the board can be used to seal the keel structure.

9.單面門套用9厘板打底(凸窗應注意窗簾位置)。其他與雙面門套同。入戶大門可封單邊實木線條門套。

9. Use a 9mm board as the base for single-sided door frames (pay attention to the position of the curtains for protruding windows). Other items are the same as double-sided door frames. The entrance door can be sealed with single-sided solid wood line door frames.

10.窗套不宜包臺面,臺面用大理石鋪貼(防盜網宜在窗套面板封后制作)。單面門套:在原來有門的基礎上起裝飾作用,不起承受門的力量。

10. The window cover should not cover the countertop, and the countertop should be paved with marble (the anti-theft net should be made after the window cover panel is sealed). Single sided door frame: It serves as a decorative function on the basis of the original door and does not withstand the force of the door.

以上的文章由濟南誠耐金屬制品有限公司德州電梯不銹鋼包邊提供分享，更多內容請關注我們：http://m.diaolan88.com

The above article is shared by Jinan Chengnai Metal Products Co., Ltd. Dezhou Elevator Stainless Steel Edge Wrapping. For more content, please follow us: http://m.diaolan88.com